CNC Lathes, Milling Machines & Engine Lathes
Four Categories.
Twenty-Three Models.
Every machine on this page is cast, fabricated and machined at our own plant in Nanhai District, Foshan. Figures below are taken directly from our factory specification sheets. Full parameter sheets and drawings are available on request.
Start From the Part, Not the Catalogue
Enter the size of the part you need to machine. This runs against the same specification tables printed further down this page — nothing else. It narrows the range; it does not replace a drawing.
Enter at least one dimension above.
Horizontal CNC Lathes & Gang-Tool Machines
Four horizontal CNC lathes in the CK series, plus two slant-bed gang-tool machines for small turned parts in volume. The gang-tool machines have no tailstock and a different structure — they are listed separately below so the comparison stays honest.
| Model | Swing over bed | Max workpiece length | Spindle bore | Spindle nose | Max speed | Main motor | Control |
|---|---|---|---|---|---|---|---|
| CK6166DH-1000Flagship | Ø660 mm | 1,000 mm | Ø105 mm | A2-11 | 1,200 r/min | 11 kW | On request |
| CK6150B-1000 | Ø500 mm | 1,000 mm | Ø82 mm | A2-8 | 1,600 r/min | 7.5 kW | On request |
| CK6140A-750 | Ø400 mm | 750 mm | Ø46 mm | C6 | 1,600 r/min | 5.5 kW servo | GSK 980TB3i |
| CK6140H-750 | Ø400 mm | 750 mm | Ø58 mm | A2-6 | 2,500 r/min | 5.5 kW servo | GSK 980TB3i |
For Small Turned Parts in Volume
One-piece slant-bed casting with a gang-type tool plate. No tailstock — bar work and chucked parts only, but far shorter tool-change and index times than a turret lathe.
| Model | Swing over bed | Max bar capacity | Spindle bore | Spindle nose | Max speed |
|---|---|---|---|---|---|
| 46SGang Tool | Ø350 mm | Ø45 mm bar | Ø56 mm | A2-5 | 4,500 r/min |
| 52PGang Tool | Ø460 mm | Ø50 mm bar | Ø66 mm | A2-6 | 3,500 r/min |
Bed-Type CNC Milling Machines
Three-axis machines with GSK controls and absolute-encoder servo motors. XKM40B is the only model in this line with an automatic tool changer; XKM3 and XKM4 are cantilever-column machines with longer travels but no magazine.
| Model | Table | X / Y / Z travel | Spindle taper | Max speed | Spindle motor | Tool magazine | Control | Weight |
|---|---|---|---|---|---|---|---|---|
| XKM40BATC | 1,570 × 320 mm | 1,000 / 450 / 400 mm | BT40 | 8,000 r/min | 3.7 kW | 12-tool, pneumatic | GSK 980MDi | 1,500 kg |
| XKM40A | 1,570 × 320 mm | 1,000 / 450 / 400 mm | R8 or NT30 | 5,440 r/min | 2.2 kW | — | GSK 980MDi | 1,300 kg |
| XKM3 | 1,270 × 254 mm | 700 / 300 / 400 + 100 mm | R8 or NT30 | 70–4,600 r/min | 2.2 kW (3 HP) | — | GSK 980MDi | 1,300 kg |
| XKM4Cantilever | 1,370 × 254 mm | 800 / 350 / 430 + 100 mm | R8 or NT30 | 70–4,600 r/min | 2.2 kW (3 HP) | — | GSK 980MDi | 1,400 kg |
Turret Mills — Manual and Power Feed
These are not CNC machines. They are Bridgeport-type vertical knee mills with manual handwheels, optional power feed and optional DRO. They compete on price and simplicity, not on cycle time — if you need programmed three-axis work, look at the XKM series above instead.
| Model | Table | X / Y / Z travel | Spindle taper | Spindle speeds | Spindle motor | Slideways | Weight |
|---|---|---|---|---|---|---|---|
| M5Top of line | 1,370 × 305 mm | 800 / 440 / 480 mm | NT40 | 70–3,600 r/min, 10 steps | 5 HP | X dovetail / Y-Z box | 1,600 kg |
| M5A | 1,370 × 280 mm | 800 / 430 / 400 mm | NT40 | 70–3,600 r/min, 10 steps | 5 HP | X dovetail / Y-Z box | 1,500 kg |
| M4 | 1,370 × 254 mm | 820 / 430 / 440 mm | R8 or NT30 | 80–5,440 r/min, 16 steps | 3 HP | X dovetail / Y-Z box | 1,400 kg |
| M4A | 1,270 × 254 mm | 730 / 400 / 400 mm | R8 or NT30 | 80–5,440 r/min, 16 steps | 3 HP | X dovetail / Y-Z box | 1,200 kg |
| M3 | 1,270 × 254 mm | 760 / 400 / 400 mm | R8 or NT30 | 80–5,440 r/min, 16 steps | 3 HP | Full dovetail | 1,200 kg |
Conventional Lathes — Two Weight Classes
Eight models in two families. The A-series are lighter machines for general shop work; the B-series have a higher centre height, an Ø82 mm spindle bore and bed lengths up to 3,000 mm. Models with a 2 in the number (C6232A, C6240A, C6240B, C6250B) are the gap-bed versions of the C6132A, C6140A, C6140B and C6150B respectively, with a saddle slot for large-diameter work.
| Model | Centre height | Swing over bed | Workpiece length options | Spindle bore | Spindle speeds | Main motor |
|---|---|---|---|---|---|---|
| C6132AA-Series | 175 mm | Ø350 mm | 750 / 1,000 mm | Ø46 or Ø54 mm | 25–1,600 r/min | 3 / 4.5 kW |
| C6232AA-Series · Gap bed, Ø520 slot | 175 mm | Ø350 mm | 750 / 1,000 mm | Ø46 or Ø54 mm | 25–1,600 r/min | 3 / 4.5 kW |
| C6140AA-Series | 202 mm | Ø400 mm | 750 / 1,000 / 1,500 mm | Ø46 or Ø54 mm | 25–1,600 r/min | 3 / 4.5 kW |
| C6240AA-Series · Gap bed, Ø580 slot | 202 mm | Ø400 mm | 750 / 1,000 / 1,500 mm | Ø46 or Ø54 mm | 25–1,600 r/min | 3 / 4.5 kW |
| C6140BB-Series | 210 mm | Ø420 mm | 1,000 / 1,500 / 2,000 mm | Ø82 mm | 90–1,600 r/min | 7.5 kW |
| C6240BB-Series · Gap bed, Ø630 slot | 210 mm | Ø420 mm | 1,000 / 1,500 / 2,000 mm | Ø82 mm | 90–1,600 r/min | 7.5 kW |
| C6150BB-Series | 250 mm | Ø500 mm | 1,000 / 1,500 / 2,000 / 3,000 mm | Ø82 mm | 90–1,600 r/min | 7.5 kW |
| C6250BB-Series · Gap bed, Ø710 slot | 250 mm | Ø500 mm | 1,000 / 1,500 / 2,000 / 3,000 mm | Ø82 mm | 90–1,600 r/min | 7.5 kW |
SBS Power Feed Units
An accessory, not a machine tool: a table power-feed unit fitted to milling machines. Exported under the SBS name alongside our machines, and machined on the same floor.
Heat-Resistant Windings
Enamelled copper windings rated for continuous duty, so the unit holds its feed rate through a long cut rather than drifting as it warms.
Balanced Rotor
Weight-relieved, dynamically balanced rotor with a cooling-vane structure — less vibration transmitted into the table.
Aluminium Bearing Housing
Aluminium alloy housing carries heat away from the bearing seat, so the rotor is less prone to heating up and distorting.
Symmetrical Cooling
Cooling is balanced in both directions of rotation, so forward and reverse feed wear the unit evenly.
Fits Our Mills
Supplied fitted to M-series turret mills, or separately for other machines — tell us the table and axis and we will confirm the mounting.
Dealer Quantities
Available in container quantities for dealers who stock milling machine accessories. Ask for the dealer price list.
Which Model Fits Your Part?
No need to fill anything in twice. Tell us the part, the material and the quantity per year, and an engineer replies with a model and the configuration it needs — not a general price list.
- Drawing, sketch or photo — with the two or three dimensions that actually matter
- Material grade, and how many pieces per batch
- Supply voltage, phase and frequency — the machine is wired to it before it ships
- Destination port, for freight and for whether a CE declaration is needed
sales@jxjmachinery.com
+86 757 8566 5555